Munchkin Doll CCD 0113 001 REV1 User Manual

FRONT  
Figure 2  
WARNING:  
Do not let child take a  
bottle to bed or self-feed for long periods. Continuous and  
prolonged sucking of fluids will cause tooth decay. To prevent  
possible choking hazard, test strength of nipple by pulling on  
bulb portion. Discontinue if any tear or crack appears on  
nipple. Do not allow child to use the nipple as a teether. Always  
test temperature of liquid before feeding baby. Do not warm  
contents in a microwave oven. Do not let child walk or run  
while carrying bottle. Do not leave child unattended. This is not  
a toy. Keep all components not in use out of the reach of  
children. Discard and replace at first sign of weakness or  
damage. Discard all packaging components before use.  
instructions  
Screw the collar onto the thread of the bottle in a  
clockwise direction to securely tighten the collar. When  
assembling the cap, make sure to place the cap vertically  
onto the bottle so the nipple sits upright and is sealed.  
4oz / 118ml  
8oz / 237ml  
bottles  
PRODUCT AND DESIGN ARE TM & ©2013 MUNCHKIN, INC.  
MUNCHKIN, THE LATCH LOGO, AND IT’S THE LITTLE  
THINGS ARE TRADEMARKS OR REGISTERED TRADEMARKS  
OF MUNCHKIN, INC. 7835 GLORIA AVE., VAN NUYS, CA  
91406. PATENT: HTTP://WWW.MUNCHKIN.COM/PATENTS.  
MADE IN CHINA/FABRIQUÉ EN CHINE.  
Compatibility: Only use Munchkin LATCH nipples  
with Munchkin LATCH bottles. Replacement nipples  
are available separately. Make sure that you are  
feeding your baby  
with the correct flow  
0m+  
3m+  
6m+  
rate nipple.  
CCD-0113-001 REV1  
BACK  
Instructions for use: Wash and inspect before use.  
Top rack dishwasher safe. Safe for boiling and steam  
sterilizing. Safe for all ages.  
Assembly: Before each use, hold  
the tip of the valve (triangular  
head) up to the light to see the  
slit and pinch apart to ensure  
proper venting. When assembling  
your LATCH bottle, first push the  
valve firmly through the hole at  
the bottom of the bottle. Make  
Figure 1  
Visible gap  
with valve  
inserted  
Nipple  
Collar  
Sterilizing: Before first use, disassemble the bottle  
and place all bottle parts in boiling water for  
5 minutes or use the Munchkin® SteamGuard™  
Microwave or Electric Sterilizer for proper hygiene.  
Cap  
sure that the triangular head of the valve is fully inserted.  
A fully inserted valve will have a visible gap between the  
bottom edge of the triangular head against the hole  
opening at the bottom of the bottle. You may not always  
see a gap unless you apply upward pressure with your  
thumb, as you inspect. (see Figure 1)  
Cleaning and Maintenance: Carefully disassemble  
the bottle. To remove the valve from the bottom of  
the bottle, grasp any portion of the circular  
flange/disc and pull outward until loose. Wash and  
rinse each piece separately and thoroughly. Carefully  
clean valve to avoid tearing. Sterilize using a sterilizer  
or boil for 5 minutes. All components are top rack  
dishwasher safe. Use dishwasher basket to secure  
components during wash and dry cycles.  
Bottle  
Sealing Disc  
Next, pull the nipple through the collar, ensuring that the  
flanges are tucked underneath. It is easier to assemble if you  
pull the nipple back and forth upwards, instead of pulling it  
up straight. Make sure the 3rd segment under the accordion  
is resting above the collar. The area where the nipple and  
collar meet should be flush (no gap). (see Figure 2)  
Valve  
 

Miele Refrigerator KF 7564 S ed 3 User Manual
Miller Electric Air Compressor AC Generator Air Compressor User Manual
Minolta Printer Magicolor 7450 User Manual
NETGEAR Switch EN104TP User Manual
New Balance Headphones NB447 User Manual
Nokia Cell Phone RM 240 User Manual
NordicTrack Home Gym 831237651 User Manual
Packard Bell Personal Computer M5801 User Manual
ParaBody Home Gym 874104 User Manual
Paradyne Network Card 9161 A2 GN10 40 User Manual